Expert Support
Available 24/7 via chat
Available 24/7 via chat
Collection list
Irrigation BOM Calculators
Planning-level irrigation bill of materials for benches/tables, grow rooms, and water rooms. Use the results to spec consumables and core components, then validate final sizing against layout, pressure losses, and operating setpoints.
Guidance only. Final pipe sizing, pump selection, and pressure regulation should be confirmed using exact zoning, emitter curves, filtration requirements, and TDH calculations.
Use 1 for single tables. For multi-tier racks, enter total levels.
Used to estimate plant count per table level.
Used for applied volume estimate (not for instantaneous flow sizing).
Planning count of laterals across table width.
Adds allowance for cuts, routing, and spares.
Used to estimate per-zone flow and valve counts.
Planning length; refine after routing.
Rule-of-thumb only; confirm with friction loss.
Typically equals your facility simultaneous irrigation flow.
Planning allowance for pipe + fittings + filters.
Run Calculate on the tabs you need first, then build the consolidated BOM. This aggregates duplicate items (same item + UOM) across the computed tabs.
Nutrients Delivery Systems Configurator
Configure an inline injection or batch-mix nutrient delivery system based on irrigation flow, number of zones, dosing channels, and water-room constraints. Use the results to build a planning BOM and align the right equipment architecture for your facility.
Planning-level guidance only. Final selection must be validated against water chemistry, pressure losses, irrigation scheduling (simultaneous zones), injector pump curves, and local plumbing codes/backflow requirements.
Typical flow when one irrigation zone/room loop is running.
Used to estimate peak injection flow (critical for sizing).
Optional. If provided, this overrides Flow per zone × Simultaneous zones.
City/well feed pressure before filtration/PRV losses.
Typical drip operating range (varies by emitter/regulators).
Used to estimate stock tank consumption and tank sizing.
Choose the approach you prefer; calculator will flag fit/risk based on inputs.
Helps determine filtration requirements and control recommendations.
Fine filtration upstream helps protect injectors/valves and reduce clogging risk.
Typical: 2-part (A/B), plus optional CalMag, additives, pH control.
A 1:100 ratio means 1 part concentrate per 100 parts water.
Common dosing bands: 50–500. Higher X = weaker injection per channel.
Used when Dose format is percent. Example: 1.0% per channel.
EC/pH targets typically require a controller, sensors, and metered dosing.
Planning: size each stock tank to cover daily usage × autonomy days.
Adds buffer for recipe swings, staffing, and refill lag.
High-frequency and recirc setups generally benefit from tighter control.
Helps bias toward proportional vs metered dosing architecture.
Strongly recommended for metered dosing and troubleshooting.
Featured House Brands, Imported Brands & Distributed Brands
Bulk-Ready Grow Media for Commercial Cultivation
Hydrotek works with cultivation teams and purchasing departments to source reliable grow media at scale. From coco and rockwool to pots and propagation supplies, we support volume programs designed to reduce freight costs, optimize cost efficiency, simplify reordering, and keep production on schedule.
- Reliable inventory
- Commercial-grade quality
- Optimized purchasing workflows for grow operations, multi-site operators, and retailers.
COMMERCIAL EQUIPMENT PROGRAMS
Buildout, Expansion & Retrofit Assistance
Hydrotek supports commercial cultivation teams, contractors, and consultants with equipment selection, project pricing, and freight-ready delivery for new facility buildouts and upgrades.
- Equipment sizing & specification support aligned to rooms, canopy, and electrical service
- Direct-from-factory pricing on select brands and equipment categories
- Bundle discounts across equipment types (lighting, climate, irrigation, benches)
- Group-buy eligibility for cost-effective sourcing on multi-room or multi-site deployments
- Staged releases, palletized freight, and jobsite / 3PL coordination
Tip: You don’t need final SKUs. Share your scope and timeline—our commercial team will respond within 48 hours.
What to include
- Facility location + project timeframe
- # rooms and approximate dimensions
- Target canopy or plant count
- Voltage / phase available (if known)
- Desired equipment categories
Common requests
- CAPEX budgeting and equipment bundles
- Alternates / substitutions to hit lead times
- Standardization across multiple rooms or sites
- Freight planning and staged deliveries